Kk2.1.5 Multi-rotor LCD Flight Control Board With 6050mpu And Atmel 644PA is next big evolution of the first generation KK flight control boards. The KK2.1.5 was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts.

The LCD screen and built-in software make install and setup easier than ever. A host of multi-rotor craft types are pre-installed, simply select your craft type, check motor layout/propeller direction, calibrate your ESCs and radio and you’re ready to go! All of which is done with easy to follow on-screen prompts! The KK gyro system has been updated to an incredibly sensitive 6050 MPU system making this the most stable KK board ever and allowing for the addition of an auto-level function. At the heart of the KK2.1.5 is an Atmel Mega644PA 8-bit AVR RISC-based microcontroller with 64k of memory.

An additional polarity protected header has been added for voltage detection, so no need for on-board soldering. A handy piezo buzzer is also included for audio warning when activating and deactivating the board. The KK2.1.5 added polarity protection to the voltage sense header and a fuse protected buzzer outputs, in case something is accidentally plugged in incorrectly. The voltage sense line has been updated for better accuracy. The board is clearly labeled and the voltage sense line color has been changed to red for easy identification, making installation and connections a snap. If you’re new to multi-rotor flight or have been unsure about how to setup a KK board then the KK2.1.5 was built for you. The 6 Pin USBasp AVR programming interface ensures future software updates will be quick and easy.

The KK gyro system has been updated to the incredibly sensitive 6050 MPU system making this the most stable KK board ever and adds the addition of an auto-level function. At the heart of the KK2.1 is the ATMEL Mega 644PA 8-bit AVR RISC-based microcontroller with 64k of memory. An additional header has been added for voltage detection, so now there is no need for onboard soldering. A handy piezo buzzer is also included with the board for audio warning when activating and deactivating the board, which can be supplemented with an LED for visual signaling. A host of multi-rotor craft types are pre-installed, simply select your craft type, check motor layout and propeller direction, calibrate your ESCs and radio and you’re ready to go. All of which is done with easy to follow on-screen prompts. If you’re new to multi-rotor flight or have been unsure about how to set up a KK board then the KK2.1 was built for you. The 6 Pin USB asp AVR programming interface ensures future software updates will be quick and easy.

What is a Multi-Rotor Control board you ask?

The KK2.1.5 Multi-Rotor controller is a flight control board for multi-rotor aircraft (Tricopters, Quadcopters, Hexcopters etc). Its purpose is to stabilize the aircraft during flight. To do this it takes the signal from the 6050MPU gyro/acc (roll, pitch, and yaw) then passes the signal to the Atmega644PA IC. The Atmega644PA IC unit then processes these signals according to the user’s selected firmware and passes control signals to the installed Electronic Speed Controllers (ESCs). These signals instruct the ESCs to make fine adjustments to the motors rotational speed which in turn stabilizes your multi-rotor craft.

The KK2.1.5 Multi-Rotor control board also uses signals from your radio systems receiver (Rx) and passes these signals to the Atmega644PA IC via the aileron, elevator, throttle and rudder inputs. Once this information has been processed the IC will send varying signals to the ESCs which in turn adjust the rotational speed of each motor to induce controlled flight (up, down, backward, forward, left, right, yaw).

Note: It is all ways recommended to update to the latest software version as part of your initial setup.(this is different than v1.6 for 2.0) 


Features:

1.     Auto Level

2.     Standard 6 Pin AVR Interface

3.     1520us(5 channels) Signal from the receiver


Firmware Version: 1.6:

1.     Pre-installed firmware., Dualcopter, Tricopter

2.     Y6, Quadcopter +, Quadcopter X, Hexcopter +, Hexcopter X, Octocopter +, Octocopter X

3.     X8 +, X8 X, H8, H6, V8, V6

4.     Aero 1S Aileron, Aero 2S Aileron

5.     Flying Wing

6.     Singlecopter 2M 2S, Singlecopter 1M 4S

7.     Custom Mix via the “Mixer Editor” option:

o    The Mixer Editor allows you to adjust where and how much signal the motors receive from stick input and sensors. This allows you to create any configuration possible with up to 8 motors or servos.


Package Includes:

1 x KK2.1.5 MULTI-ROTOR LCD FLIGHT CONTROL BOARD
2 x Connecting Cables
1 x Piezo buzzer

 



Write a review

Note: HTML is not translated!
    Bad           Good
Captcha

KK2.1.5 MULTI-ROTOR LCD FLIGHT CONTROLER

  • Product Code: HLI0133
  • Availability: 10
  • Rs.2,400

  • Ex Tax: Rs.2,034